MONO SV 100
OC/CSII/Wc2

MONO SV 100

SINGLE LAYER WHITE PLASTER

Ready mortar based on high-strength Portland white cement (I-52.5), white marble fine-grained aggregates, calcium hydroxide, and special additives to improve adhesion. Simply mix with water. It minimizes material preparation time and increases the speed of application.

PACKAGING:

25Kg

40Kg

COLOR:

White

CHARACTERISTICS:

Application Temperature

+5°C to +35°C

Application Tools

Trowel, special mixer machine M-TEC

Consumption

Approx. 12 – 14kg of mortar per m² for a layer with 1 cm thickness

Specific Weight of Fresh Mortar

1650 kg/m³

Water Demand

  • 8,0 – 8,5 lt/40 kg
  • 5,0 – 5,3 lt/25 kg

Download the relevant technical files:

Uses

Use it as one-coat plaster, on exterior and interior surfaces, after having applied SV1 (high-strength cement primer plaster). It replaces roughcasting and marble –based finish-coat plaster, combining both in one coat. The layer thickness should not exceed 2 cm. Apply it just like render and scrub like marble–based finish-coat plaster. Due to the nature and the fine granulometry of the marble powder (< 1,2 mm), it gives a white and smooth final surface ready for scrubbing and painting. In special cases, the product can be reinforced by adding MARMOLINE MP 20 acrylic dispersion.

Advantages

  • High strength
  • Excellent adhesion
  • Moisture- and frost-proof
  • Indoor and outdoor use
  • Easy to apply
  • Excellent workability
  • Increased productivity
  • Reduced labour cost
  • Smooth – White surface
  • Fast to prepare
  • Stable quality
  • Check the application surface so that to be clean. SV1 cement primer plaster must have been previously applied.
  • Saturate the surface with water, especially in hot summer months and apply.
  • Mix by hand or using special machines (mixers – pumps), supplied by MARMOLINE, which make work simpler and faster
  • For better results, it is recommended to attach MARMOLINE corner beads. The use of corner beads enhances application’s performance, while ensuring the strength of the corners against micro-bumps, and the perfect aesthetics of the finished surface.
  • Avoid the use of removable metal plaster guides. Use galvanized MARMOLINE metal plaster guides. If this is not possible, you should fill well the groove, after removing the metal plaster guides, in order to avoid cracks.
  • Do not use other materials (such as gypsum etc.) to fix the plaster guides and the corner beads.
  • Apply with the special machine (pump). In small surfaces, you can apply the mix by hand, using a trowel.
  • Apply in one coat, up to 2 cm thick. For thicker layers, it is recommended to fill with SV2 base coat plaster.
  • On the joints of different structural elements, on the insulators and anywhere else needed, fix the MARMOLINE fibreglass mesh. It is extremely important for the proper function of the fibreglass mesh to place it to a depth of 0.5 cm from the exterior surface of the plaster.
  • On surfaces covered with insulation boards (EPS-XPS), in order to avoid cracks you must cover them with an appropriate MARMOLINE fiberglass mesh, in combination with the polymer modified adhesive MARMOLINE FK 202. In this case, SV100 plaster should be applied at least 15 days after the FK 202 application.
  • Leave the wet mortar to set and smooth out any existing flaws with a large metal spatula.
  • Moisten slightly the surface with water and float by means of an EPS or a rough sponge to obtain a surface ready for puttying and painting.
  • For the next two to three days, especially during summer, we recommend frequent sprinkling of the plaster, with water, to eliminate the possibility of cracking.
  • The setting time depends on the season (temperature and humidity). In winter, such time can be over 2 hours, while in warm summer period it can be less than an hour.
  • As with all plasters, we recommend that you verify the applied material is thoroughly dry before painting the surface
  • Mixing ratio: 8,0 – 8,5 lt/40 kg & 5,0 – 5,3 lt/25 kg.
  • Application temperature +5°C to +35°C.